Micromod MOD: MODCELL Multiloop Processor 2002N Model C and Bedienungsanleitung PDF herunterladen (Seite 24)

MODCELL Multiloop Processor

MECHANICAL INSTALLATION

Table 2-1. Module Types and Suggested Locations

Block

Type

Module Type

Module Location

1 to 16 17 to 32

VCIM

2001A Voltage Input

2002A Current Input

2012A Current Input with 2-Wire Transmitter

Note 1 X

RIM 2009A RTDInput (2 Wire) Note 1 X

WRIM 2009A RTDInput (3 Wire) Note 1 Note 3

TIM

2013A Thermocouple Input

with Upscale Burnout Detection

Note 1 X

AOM 2003A Current Output Note 1 X

DIM

2004A Solid State Relay Input

2006A Nonisolated Digital Input

X Note 2

DOM

2005A Solid State Relay Output

2007A Nonisolated Digital Output

X Note 2

DDOM

WDOM

2011A Mechanical Relay Output (SPST)

2011A Mechanical Relay Output (Form C)

Note 3

Notes 2,

RIO 2020N Remote I/O Interface Note 3 Note 3

ICN 2030N ICN Communication ––––––––– Note 4

MSC

2033N RS-232 Communication

2032N RS-485 2-Wire Communication

2034N RS-485 4-Wire Modbus Communication

____ Note 5

Notes:

1. These locations can be used for analog modules if locations 17 - 32 are occupied.

2. These locations can be used for discrete modules if locations 1 - 16 are occupied.

3. Module occupies two locations.

4. ICN Module occupies two locations and may be in locations 25 through 32 only.

5. RS-232 Module and RS-485 4-Wire Module are double wide modules that can occupy

slots 31-32 (Port 1), 28-29 or 29-30 (Port 2), 25-26 or 26-27 or 27-28 (Port 3).

RS-485 2-Wire Module is a single wide module that can occupy slot 32 (Port 1), 29 or

30 (Port 2), 26 or 27 or 28 (Port 3).

! CAUTION Module group S25 to S32 is reserved for modules whose circuits are rated less than

30V rms 42.4V peak or 60Vdc. Module locations within a group (S1 to S8, S9 to S16

and S17 to S24) must all

be rated less than 30V rms or 42.4V peak or 60Vdc or must

all

be rated for greater than 30V rms or 42.4V peak or 60Vdc.Do not mix modules

employed in circuits rated less than 30 V rms or 42.4V peak or 60Vdc with modules

used in circuits greater than 30V rms or 42.4V peak or 60Vdc within the same group.

WARNING Do not use any I/O module which i s not listed in Instruction Notice 92902-98 (back of

book). When used in flush mount controller, the listed modules are FM Approved and

CSA Certified for use in Class I, Division 2, Group A, B, C or D hazardous (classified)

locations. Substitution of a module not on the list voids the Approval/Certification.

WARNING Do not use a 2011A Mechanical Rel ay Output Module when the installation

environment contains chemicals which can degrade the materials used to seal the

relay in the module. The sealing materials are as follows:

• Polybutylene Terephthalate, Po lyplastics Co. Ltd., Compound No. 3270

• Polyphelene Suffide, Summitomo Chemical Co. Ltd., Compound No. 3601GL30

• Epoxy Resin, Summito Bakelite Co. Ltd., SUMIMAC ECR-9107K

Degradation of the relay seal voi ds the Approval/Certification of the instrument for use

in Class I, Division 2, Group A, B, C or D hazardous (classified) locations.

1 2 ... 19 20 21 22 23 24 25 26 27 28 29 ... 81 82

Kommentare zu diesen Handbüchern

Keine Kommentare

Micromod MOD: MODCELL Multiloop Processor 2002N Model C and Bedienungsanleitung Seite 24

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Ausrüstung Micromod MOD: MODCELL Multiloop Processor 2002N Model C and