Micromod Micro-DCI: 53SL6000 Single Loop Controller Bedienungsanleitung Seite 35
- Seite / 138
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Figure 3-9. Editing a tAG
3.6 Entering a Pass-Key
In engineering mode, access to the ProG and conF
menus can be selectively restricted, as each menu
has its own pass-key capabilities. A pass-key is a
four digit number that must be entered when a
menu is selected; otherwise, access to module
prompts in that menu are prohibited. Figure 3-10
illustrates the key display that appears if a menu is
pass-key protected.
Figure 3-10. KEY? Prompt
The correct pass-key must be entered in the red
dro with the following procedure:
1.
Press the scroll forward pb until the desired
number for the first digit appears (assumes
first digit is not a zero).
2.
Press the position select right pb; the second
zero starts blinking.
3.
Repeat steps 1 and 2 to enter all four pass-key
digits.
4.
Press the enter pb; if the pass-key is correct
engineer mode functions are permitted for that
menu.
NOTE:
If the pass-key can not be recalled, then
the database must be defaulted using the
procedure described in Section B.5.
3.6.1 Configuring a Pass-Key
To configure a conF (or ProG) pass-key, the follow-
ing steps must be performed:
1.
Enter engineer mode by pressing and holding
the mode pb until a menu prompt appears in
the green dro.
2.
Press the scroll forward pb until conF (ProG)
appears in the green dro.
3.
Press the enter pb to accept the conF (ProG)
menu.
4.
If KEY does not appear in the yellow dro, press
the scroll forward pb until it does.
5.
Press the enter pb to select the KEY prompt.
cKEY (PKEY) appears in the green dro.
It is assumed the pass-key was never config-
ured before and that four zeros appear in the
red dro:
6.
Press the enter pb; the leftmost number (zero)
in the red dro blinks.
7.
Press the scroll forward pb until the desired
number appears (assumes zero will be
changed to a different number).
8.
Press the shift right pb; the next zero starts
blinking.
9.
Repeat steps 7 and 8 until all four pass-key
digits are entered.
10.
Press the enter pb to enter the pass-key.
11.
Press the mode pb to exit engineer mode.
3.7 Offline Display Pattern
The controller offline state is indicated by four acti-
vated double LED markers along the green vertical
bar as shown in Figure 3-11. The remainder of the
vertical bar is dark.
Events that can cause the controller to be offline
are as follows:
• If a ProG menu parameter is altered in engi-
neer mode , it causes the controller to immedi-
ately go offline,
53SL6000 Instruction Manual Section 3. Display Panel
3-8
- INSTRUCTION MANUAL 1
- MicroMod Automation, Inc 2
- Table of Contents 3
- 4.0 Functional Overview 4-1 4
- 5.0 Inputs/Outputs (I/O) 5-1 4
- 9.0 Commissioning 9-1 6
- Appendix A: Glossary A-1 7
- Appendix D: Prompt List D-1 7
- List of Tables 8
- List of Figures 9
- Safety Summary 11
- READ FIRST 12
- 1.0 Introduction 13
- 1.2 Controller Model Numbers 15
- 1.3 Product Specifications 15
- Thermocouple List 18
- 2DI/2DO Option Module 18
- CPU Cycle Time 19
- Control Ranges 19
- 2.1 Inspection 20
- 2.2 Site Location 20
- 2.3 Panel Mounting 20
- 2.4 Power Connections 20
- 2.5 Signal Connections 22
- 2.5.4 Analog Output AO1 23
- Signal Wiring 24
- 2.7 2DI/2DO Module 25
- 2.9 Applying Power 26
- 2.9.1 Power-up Sequence 27
- 3.0 Display Panel 28
- 3.4 Operator Mode Overflow/ 31
- Underflow Indication 31
- 3.5 Engineer Mode 32
- Backward 33
- 3.6 Entering a Pass-Key 35
- 3.7 Offline Display Pattern 35
- 3.9 Display Alphanumerics 38
- 3.10 Engineer Mode Summary 38
- 4.0 Functional Overview 40
- 4.2 Detailed Block Diagram 41
- 5.0 Inputs/Outputs (I/O) 45
- Parameter Entries 46
- Table 5-6. RTD Types 47
- 5.4 Analog Output 1 (AO1) 48
- 5.5 Discrete Inputs 49
- 5.6 Discrete Outputs 49
- 6.1 Section Overview 51
- 6.2 Characterizer 51
- 6.2.1. 3SEG Mode 52
- 6.2.2 LSEG Mode 52
- 6.2.3 PrGM Mode 53
- 6.3 Math Function Block 54
- 6.3.1 ALG Mode 55
- 6.3.2 SuMM Mode 55
- 6.3.3 PoLY Mode 56
- 6.3.4 PoWr Mode 56
- 6.3.5 LoG Mode 56
- 6.3.6 LiM Mode 56
- 57
- 7.0 Control Scheme Block 59
- Schemes 64
- Control Scheme 65
- 7.7 Control Loop Parameters 83
- 7.8 Control Scheme Signal 86
- 8.0 Eight Control Strategies 88
- 8.2 Analog Back-Up Control 90
- 8.3 Ratio Control 92
- 8.4 Auto/Manual Selector 94
- Out 95
- 8.4.8 SchM Selection 95
- 8.5.2 AI2 - Primary PV Input 96
- 8.6.1 AI1 - Primary PV Input 98
- 8.7 Dual Indicator with 100
- Re-Transmitted PV 100
- Control 101
- 8.8.3 Speed Factor Adjusting 103
- 9.0 Commissioning 104
- 9.8 Easy-Tune 106
- Actual Curve 107
- Approximated Curve 107
- 9.8.1 Executing Easy-Tune 108
- Appendix A: Glossary 112
- B.1 Overview 118
- B.2 Parts List 118
- B.3 Removal and Replacement 119
- Procedure 120
- B.5 Defaulting the Database 123
- B.6 Analog Input/Output 123
- Calibration Values 123
- B.7 Watchdog LED 123
- C.1 Overview 124
- C.2 Configuring the System 124
- Module for Datalink 124
- C.3 Protocol 124
- C.3.1 Message Types 125
- C.3.2 Transaction Examples 125
- Reference 126
- Cross Reference 128
- Reference 129
- via Datalink 131
- Appendix D: Prompt List 132
Verwandte Produkte und Handbücher für Ausrüstung Micromod Micro-DCI: 53SL6000 Single Loop Controller
Ausrüstung Micromod Micro-DCI: 53MC5000 Multi-Loop Process Controller Bedienungsanleitung
(99 Seiten)
(99 Seiten)
Ausrüstung Micromod Micro-DCI: 53MC5000 Multi-Loop Process Controller Bedienungsanleitung
(123 Seiten)
(123 Seiten)
Ausrüstung Micromod Micro-DCI: 53IT5100B Micro-DCI 4-Channel Indicator Bedienungsanleitung
(71 Seiten)
(71 Seiten)
Ausrüstung Micromod Micro-DCI: 53MC5000 Multi-Loop Process Controller Bedienungsanleitung
(201 Seiten)
(201 Seiten)
Ausrüstung Micromod Micro-DCI: 53SL5100A Single Loop Controller Rev. 1 Bedienungsanleitung
(6 Seiten)
(6 Seiten)
Ausrüstung Micromod Micro-DCI: 53ML5100A LOADING STATION REV. 1 FIRMWA Bedienungsanleitung
(20 Seiten)
(20 Seiten)
Ausrüstung Micromod Micro-DCI: 53IT5100A Indicator/Totalizer Rev. 1 Fi Bedienungsanleitung
(4 Seiten)
(4 Seiten)
Ausrüstung Micromod MOD: 1800P - MOD 30ML Identity Module (Version 2) Bedienungsanleitung
(70 Seiten)
(70 Seiten)
Ausrüstung Micromod MOD: 30ML and Modcell Totalization Application Gui Bedienungsanleitung
(24 Seiten)
(24 Seiten)
Ausrüstung Micromod MOD: Remote I/O Modules for use with 2020N Remote Bedienungsanleitung
(42 Seiten)
(42 Seiten)
Ausrüstung Micromod MOD: MODCELL Multiloop Processor 2002N Model C and Bedienungsanleitung
(82 Seiten)
(82 Seiten)
Mitsubishi MXZ-4A80VA Handbücher
Bedienungsanleitungen und Benutzerhandbücher für Split-System-Klimaanlagen Mitsubishi MXZ-4A80VA.
Wir stellen 1 PDF-Handbücher Mitsubishi MXZ-4A80VA zum kostenlosen herunterladen nach Dokumenttypen zur Verfügung Installationshandbuch
Kommentare zu diesen Handbüchern